CAR HEATER BLOWER MOTOR BRUSHES 8x9x22-B1
MPROVED AND ENHANCED HIGH QUALITY LONGER LASTING AND BETTER PERFORMANCE
THE BEST QUALITY AVAILABLE WITH EXTRA RELIABILITY
Do not be fooled by cheaper carbons found elsewhere here on Ebay!
Pair of replacement carbon brushes to fit most vehicle heater blower motors.
TO FIT HEATER AND BLOWER MOTOR FOR THE VEHICLES AND MOTORS LISTED BELOW:-
(This is not a comprehensive list - these high quality brushes work on a lot of 12 or 24 volt cars and as long as the measurements of the brushes shown below fit your motor it should work nicely! - Feel free to email us with any queries you may have and we will be happy to help)
Vauxhall Zafira (Known to fit 55 plate and most likely will fit many other Vauxhall models)
VW :- Passat – VW Lt35, Passat 2000
(Also Fits 8D2719021a Motor slight grinding required)
Audi :- A4, Audi 80, Avant
BMW - Most makes
Mercedes :- Sprinter ,208, 308, 1998 - sprinter 310
Vito cdo. 108d vans. Vito, Van, 108cdi
03 Sprinter 208 (may require slight filing )
C 180, C200 / C230 / C240 / C250 td/ CLK (W208) /C250TD, 98 (W202). C CLASS
Golf GTI :- MK3
Valeo 95's ,
Citroens :-Xantia 1.9 Turbo
Renaults.:- Kangoo ,Xsara
Fiat Scudo (note if you have a 2003 Scudo you may need to grind brushes slightly or cut the spring slightly to fit this)
Siemens Heater Motor
Valeo 12v n32
You get TWO carbon brushes, a pair , brand new of extremely high quality and performance!
These measure 9mm x 8mm x 22mm (The length of 22mm can be shortened easily if required by grinding off)
NOW WITH EXTRA LONG COPPER WIRES EMBEDDED INSIDE - 40MM
MOST OTHER SELLERS HAVE VERY SHORT COPPER WIRES AND YOU WILL HAVE DIFFICULTY FITTING , OURS ARE EXTRA LONG TO MAKE FITTING MUCH EASIER!!!
WHY WASTE MONEY ON A NEW MOTOR COSTING 300 POUNDS WHEN IT IS SO EASY TO REPLACE THE CARBON BRUSHES?
Signs and symptoms of Carbon brushes which are worn are:-
- The fan stops and starts , sometimes if the car jolts you will get the motor stopping or starting
- Fan does not work completely
- Fan is erratic and slows /starts/ stops by itself
To change the carbon brushes is easy ! On average it only takes 30 minutes to an hour
You need to locate your heater fan blower motor which in some cars is on the passenger side - inside the car , on the underside of the front panel facing the passenger seat - remove the flap which will be held by screws and you will locate the heater/blower/fan air motor. Search the net for diagrams for your particular model but generally these are easy to remove . Once you have the heater motor out you will see there will be two clips on the side and once you remove the clips (be careful not to loose any bits) Remove the old carbon brushes and put the new ones in and connect the copper wires in. Thats it you should have a good working fan motor/blower/heater motor as good as new!
Lots of free advise and diagrams on the internet as to how to change your brushes for your model but do contact us as we have a hugh list of sites who host free diagrams and instructions on how to change these!
IF THIS DOES NOT FIT FOR ANY REASON WE WILL ACCEPT IT BACK FOR A FULL REFUND NO QUESTIONS ASKED!
INTERNATIONAL ORDERS WELCOME!
WE HAVE SOLD HUNDREDS OF THESE TO HUNDREDS OF HAPPY PEOPLE SO PLEASE BUY WITH CONFIDENCE!
GOOD QUALITY PERFORMANCE PRODUCT - IMMEDIATE DESPATCH !